ATSAMD20J15A-AU Datasheet

Embedded - Microcontrollers, Integrated Circuits (ICs), IC MCU 32BIT 32KB FLASH

Stock & Ordering: Octopart | Findchips
ATSAMD20J15A-AU
Embedded - Microcontrollers, Integrated Circuits (ICs), IC MCU 32BIT 32KB FLASH
Atmel SAM D20J / SAM D20G / SAM D20E
ARM-Based Microcontroller
DATASHEET
Description
The Atmel Sam D20 Is A Series Of Low-power Microcontrollers Using The 32-bit Arm Cortex -m0+
Processor, And Ranging From 32- To 64-pins With Up To 256kb Flash And 32kb Of Sram. The Sam D20
Devices Operate At A Maximum Frequency Of 48mhz And Reach 2.14 Coremark/mhz. They Are Designed For
Simple And Intuitive Migration With Identical Peripheral Modules, Hex Compatible Code, Identical
Linear Address Map And Pin Compatible Migration Paths Between All Devices In The Product Series. All
Devices Include Intelligent And Flexible Peripherals, Atmel Event System For Inter-peripheral
Signaling, And Support For Capacitive Touch Button, Slider And Wheel User Interfaces.
The Atmel SAM D20 devices provide the following
Features: In-system Programmable Flash, Eight-channel Event System, Programmable Interrupt
Controller, Up To 52 Programmable I/o Pins, 32-bit Real-time Clock And Calendar, Up To Eight 16-bit
Timer/counters (tc). The Timer/counters Can Be Configured To Perform Frequency And Waveform
Generation, Program Execution Timing Or Input Capture With Time And Frequency Measurement Of Digital
Signals. The Tcs Can Operate In 8- Or 16-bit Mode, Or Be Cascaded To Form A 32-bit Tc. The Series
Provide Up To Six Serial Communication Modules (sercom) That Each Can Be Configured To Act As An
Usart, Uart, Spi And I2c Up To 400khz; Up To Twenty-channel 350ksps 12-bit Adc With Programmable
Gain And Optional Oversampling And Decimation Supporting Up To 16-bit Resolution, One 10-bit 350ksps
Dac, Two Analog Comparators With Window Mode, Peripheral Touch Controller Supporting Up To 256
Buttons, Sliders, Wheels, And Proximity Sensing; Programmable Watchdog Timer, Brown-out Detector And
power-on reset, and twopin Serial Wire Debug (SWD) program and debug interface.
All Devices Have Accurate And Low-power External And Internal Oscillators. All Oscillators Can Be
Used As A Source For The System Clock. Different Clock Domains Can Be Independently Configured To
Run At Different Frequencies While Enabling Power Saving By Running Each Peripheral At Its Optimal
clock frequency.
The Sam D20 Devices Have Two Software-selectable Sleep Modes, Idle And Standby. In Idle Mode The Cpu
Is Stopped While All Other Functions Can Be Kept Running. In Standby All Clocks And Functions Are
Stopped Expect Those Selected To Continue Running. The Device Supports Sleepwalking, Which Is The
Module's Ability To Wake Itself Up And Wake Up Its Own Clock, And Hence Perform Predefined Tasks
Without Waking Up The Cpu. The Cpu Can Then Be Only Woken On A Need Basis, E.g. A Threshold Is
Crossed Or A Result Is Ready. The Event System Supports Synchronous And Asynchronous Events,
allowing peripherals to receive, react to and send events even in standby mode.
The Flash Program Memory Can Be Reprogrammed In-system Through The Swd Interface. The Same Interface
can be used for non-intrusive on-chip debug of
Application Code. A Boot Loader Running In The Device Can Use Any Communication Interface To
download and upgrade the
Application Program In The Flash Memory. The Atmel Sam D20 Devices Are Supported With A Full Suite
Of Program And System Development Tools, Including C Compilers, Macro Assemblers, Program
debugger/simulators, programmers and evaluation kits.
42129J-SAM-12/2013
FEATURES
Processor Z Arm Cortex-m0+ Cpu Running At Up To 48mhz Z Single-cycle Hardware Multiplier
Memories Z 16/32/64/128/256kb In-system Self-programmable Flash Z 2/4/8/16/32kb Sram
System Z Power-on Reset (por) And Brown-out Detection (bod) Z Internal And External Clock Options
With 48mhz Digital Frequency Locked Loop (dfll48m) Z External Interrupt Controller (eic) Z 16
External Interrupts Z One Non-maskable Interrupt Z Two-pin Serial Wire Debug (swd) Programming, Test
and debugging interface
Low Power z Idle and standby sleep modes z SleepWalking peripherals
Peripherals Z 8-channel Event System Z Up To Eight 16-bit Timer/counters (tc), Configurable As
Either: Z One 16-bit Tc With Compare/capture Channels Z One 8-bit Tc With Compare/capture Channels Z
One 32-bit Tc With Compare/capture Channels, By Using Two Tcs Z 32-bit Real Time Counter (rtc) With
Clock/calendar Function Z Watchdog Timer (wdt) Z Crc-32 Generator Z Up To Six Serial Communication
Interfaces (sercom), Each Configurable To Operate As Either: Z Usart With Full-duplex And
Single-wire Half-duplex Configuration Z I2c Up To 400khz Z Spi Z One 12-bit, 350ksps
Analog-to-digital Converter (adc) With Up To 20 Channels Z Differential And Single-ended Channels Z
1/2x To 16x Gain Stage Z Automatic Offset And Gain Error Compensation Z Oversampling And Decimation
In Hardware To Support 13-, 14-, 15- Or 16-bit Resolution Z 10-bit, 350ksps Digital-to-analog
Converter (dac) Z Two Analog Comparators With Window Compare Function Z Peripheral Touch Controller
(PTC) z 256-Channel capacitive touch and proximity sensing
I/O z Up to 52 programmable I/O pins
Packages z 64-pin TQFP, QFN z 48-pin TQFP, QFN z 32-pin TQFP, QFN
Operating Voltage z 1.62V - 3.63V
Power Consumption Z Down To 70 A/mhz In Active Mode Z Down To 8 A Running The Peripheral Touch
Controller
Atmel SAM D20 [DATASHEET]
42129J-SAM-12/2013
1. Configuration Summary
SAM D20J
Number of pins
General Purpose I/O-pins (GPIOs)
256/128/64/32/16KB
32/16/8/4/2KB
Maximum CPU frequency